Sistema de pulverização Fuji Spray 2903-T70 Mini-Mite 3 Platinum - T70 HVLP

Name: Sistema de pulverização Fuji Spray 2903-T70 Mini-Mite 3 Platinum - T70 HVLP
Brand: Fuji Spray
SKU: 0612852903707
Price: 1487.97 EUR
Availability: InStock

Brand:Fuji Spray

3.7/5

€
1487.97

DESCRIÇÃO DO PRODUTO O sistema Mini-Mite 3 PLATINUM inclui a pistola Fuji T-Model. A Fuji instala o mesmo poderoso motor de turbina de 3 estágios usado nos modelos Q3. O MM3 PLATINUM não possui o recurso patenteado de redução de ruído visto nos modelos Fuji Q, no entanto, o nível de ruído não é maior do que qualquer outra turbina HVLP padrão. A turbina MM3 PLATINUM desenvolve aproximadamente 6 psi. Essa pressão é mais do que suficiente para pulverizar todos os revestimentos conhecidos (quando devidamente diluídos) e todos os revestimentos à base de água mais recentes. A pistola de pulverização T-70 não sangra e possui um botão de controle de padrão montado na lateral (para ajustar o tamanho do padrão do ventilador) e um copo de 1 litro. O conjunto de capas de ar padrão nº 3 (1,3 mm) é para uso em acabamento fino de uso geral. De fácil manutenção. Perfeito para profissional ou iniciante. Esta é uma máquina de classificação industrial a um preço imbatível. Caixa de metal resistente com porta-pistola. Portátil e poderoso. O sistema inclui a turbina Mini-Mite 3 PLATINUM, mangueira Hi-Flex de 25 pés, pistola de pulverização sem sangramento T-70, copo de viscosidade, escova de limpeza, chave inglesa e manual do usuário de 24 páginas. O que há de novo na série Mini-Mite PLATINUM? A Câmara de Dissipação de Calor Fuji Spray: A Fuji Spray projetou um método exclusivo para remover qualquer acúmulo de calor da caixa da turbina. O excesso de calor é canalizado para uma Câmara de Dissipação de Calor localizada na parte traseira do gabinete. Coberturas de redução de ruído do spray Fuji: As turbinas Mini-Mite PLATINUM são equipadas com um método para reduzir o ruído. As tampas de redução de ruído abrigam os filtros. DO FABRICANTE O sistema Mini-Mite 3 (MM3) inclui a nova pistola de pulverização Fuji T-Series com um botão de controle de padrão para ajustar o tamanho do ventilador de pequeno a grande. A Fuji instala o mesmo poderoso motor de turbina de 3 estágios usado nos modelos Q3. O MM3 não possui o recurso de redução de ruído patenteado como visto nos Fuji Q-Models, no entanto, o nível de ruído não é maior do que qualquer outra turbina HVLP padrão. A turbina MM3 desenvolve aproximadamente 6psi. Essa pressão é mais do que suficiente para pulverizar todos os revestimentos conhecidos (quando devidamente diluídos) e todos os revestimentos à base de água mais recentes. A pistola de pulverização incluída neste pacote é a Fuji T-70 com copo de 1 litro. O conjunto padrão de capa de ar nº 3 (1,3 mm) é para uso em acabamento fino de uso geral. De fácil manutenção. Perfeito para profissional ou iniciante. Esta é uma máquina de classificação industrial a um preço imbatível. Caixa de metal resistente com suporte de arma. Portátil e poderoso. O sistema inclui a turbina Mini-Mite 3, mangueira Hi-Flex™ de 25 pés, pistola de pulverização sem sangramento T-70 com copo de 1 litro, copo de viscosidade, escova de limpeza, chave inglesa e manual do usuário de 20 páginas.

Quantia

adicionar ao carrinho Comprar agora

EAN: 0612852903707

Categorias Ferramentas e Melhorias Domésticas, Pintura, revestimentos de parede e suprimentos, Ferramentas e suprimentos para pintura, Aplicação de tinta, Pulverizadores de pintura,

A mangueira de 25 pés inclui válvula de controle de ar para reduzir o excesso de pulverização e o ressalto. Estojo de turbina de metal com suporte de arma prático. Turbina PLATINUM com Câmara de Dissipação de Calor (HDC). Pistola de pulverização leve sem sangramento com alça ergonômica Stay-Cool. A pistola de pulverização profissional possui um botão de controle de padrão lateral conveniente para ajustar o tamanho do padrão de leque de pequeno a grande.

Brand	Fuji Spray
Color	Blue
Customer Reviews	4.7 4.7 out of 5 stars 449 ratings 4.7 out of 5 stars
Hose Length	25 Feet
Included Components	25ft Air Hose, T-70 Bottom Feed Spray Gun, Mini-Mite 3 PLATINUM Turbine
Is Discontinued By Manufacturer	No
Item Dimensions LxWxH	15 x 9.5 x 14.75 inches
Item model number	2903-T70
Item Weight	28.1 pounds
Item Weight	28.13 Pounds
Manufacturer	Fuji Spray
Material	Metal
Model Name	Fuji Spray Mini-Mite 3 Bottom Feed PLATINUM
Power Source	AC
Product Dimensions	15 x 9.5 x 14.75 inches
Style	Portable,Ergonomic
Tank Volume	0.25 Gallons

5 Star

4 Star

3 Star

2 Star

1 Star

escreva sua revisão

O seu email não será publicado. Todos os campos obrigatórios são marcados com^*

Sua avaliação

Scritto da: PJ

Great sprayer for woodworking

Before purchasing this sprayer, I had used a Graco 360 DSP airless sprayer with primer and latex paint on built-in shelving. The airless sprayer provided a nice finish on horizontal surfaces painted separately from the whole (adjustable shelves), but I couldn't get good results with assembled pieces because it laid paint down so quickly that there was zero room for error. Each pass had to be timed perfectly, and overspray was a big issue (onto surfaces painted minutes earlier but that had already started to dry, and especially in corners where painting at an angle rather than perpendicular due to the tight space caused excess paint to gather in corners and then drip and puddle). The amount of sanding and rework was unbearable, the over spray area was THICK with paint, and it used a LOT of paint. So, for my next built-in shelves I got the Mini Mite 3 with bottom cup. It worked great. Definitely get the additional whip hose and any remote control outlet. The over spray was comparably minor, it used a lot less paint, and produced great fine finish results at a slow pace for detailed work. The sprayer, cup, hose, and turbine housing are all top notch quality. Clean well after each use and it'll look good and perform well for a long time. My only frustration with cleaning was the plastic diaphragm inside the cup. I had to remove it every time to clean out paint that got behind it. Otherwise, the gun cleaned easily with the separately available cleaning kit. Definitely get that, or something similar. Water flow was not good enough to fully clean inside the feeder tube or inside the gun. After doing all I could with just water, the long, flexible pipe cleaner of the proper diameter got more paint out. I'll still use the airless sprayer for large flat surfaces, but I'll use this Fuji HVLP for all furniture projects. I had to practice a LOT on scrap wood to get the process right, but the resulting finish with a high gloss white latex paint was perfectly smooth. I'm an amateur, and I realize latex paint isn't ideal for cabinetry, but I wanted to exactly match the rest of the existing doors and trim work. I tried the #5 1.8 tip but couldn't get the finish "fine" enough (maybe due to inexperience). I ultimately used the included 1.3 tip and just diluted the paint with water until I got a 20 second pour with the included viscosity cup and ignored any dilution guidelines on the paint can. That produced great, smooth, glossy results. The one trick that helped me the most was having a large piece of cardboard or resin paper to the side of my workspace to test the spray pattern every time I adjusted the width and horizontal/vertical orientation for the various pieces and angles of the shelving. My amateur guide to getting a fine finish is to use the 1.3 tip no matter how thick your paint is, dilute to the 17-25 second range as measured by the viscosity cup, set your spray fan orientation and width, maximize air flow, fully close the paint flow control dial then open it a full turn, then spray briefly in one spot. If you see ANY spatter droplets on the outside edges, then reduce paint flow slightly and try again until there is NO spatter at the edges and you see only very fine spray everywhere. Then run a test pass or two on that paper to determine how quickly you need to move. Place a work light where you can see the wet paint reflection to verify that you have a good coat (this is especially important when painting white topcoat over white primer or when doing a second coat). Overlap passes by 50% (aim the center of the pattern at the far edge of the previous pass. If the reflection looks uneven or grainy due to lack of paint from moving too quickly, it's okay to quickly touch up freshly wet areas with short passes (this sprayer doesn't spatter when you start and stop, so I found it ok to touch-up spots in the middle of a pass without redoing the whole pass), but don't go back to touch up any area that may have already started to skin over (several passes back). Let it dry and do another coat if necessary. A word on over spray... it exists. Do not think that you can spray indoors or in a garage without taking the time to tape off the surrounding area with plastic. There was a fine mist of paint on the (plastic covered) floor or wall past wherever I had aimed the sprayer, and there was a fine, dry, thin, dusty layer throughout the whole room (and garage workspace) afterward far from where I was spraying. That paint dust was as easy to wipe off as a month of normal busy household dust, although I didn't wait to see what happened if I let that latex dust sit for a month. I wore a headlamp and could see fine spray dust floating everywhere, so wearing a respirator is important. The professionals probably do a better job of fine tuning the air flow to reduce this spray dust, but amateurs beware. Still, it's significantly less messy to work with than an airless sprayer, and you have much more fine control, and fine finish results.

Scritto da: Ryan S.

Great HVPL for the price

Was doing research on a HVLP sprayer for woodworking projects. I found good reviews on the FujiSpray systems. I went with the Mini Mite 3 Platinum with bottom feed spray gun. I have used a couple of times now a have had great results. The turbine is powerful and the gun provides a great finish. All the parts are heavy duty and easy to clean. I would recommend this HVLP for anyone who does small finishing products.

Scritto da: JakeB

Great sprayer

This is my first experience with an HVLP sprayer. It was very easy to use and figure out. The instructions were easy to understand and it left a perfect drip free finish. Would happily buy it again.

Scritto da: Jon

Well made and very nice gun!

The T70 spray gun is the best HVLP gun I've ever held in my hands. The turbine unit delivers an astonishing amount of air flow while being moderately quiet, (quieter than some compressors I've used.

Scritto da: Travis Mizzell

Excellent spray setup!

This setup is awesome. After years of spraying professionally in a custom cabinet shop, I was looking for a setup that could meet those type expectations in a hobby/semi professional type setting. This setup definitely meets those needs!

Scritto da: Samantha

Do-it-Yourself Professional Looking Trim and Cabinets

I am an avid do-it-yourselfer only when I am confident I can achieve professional looking results. Performing a whole home remodel over the past year, you can only imagine the number of surfaces that needed painting. Breaking out a roller was fine for the walls, but I definitely wanted a smooth, professional finish for my kitchen cabinets and trim work. After receiving $8-$13K quotes for painting my kitchen cabinets, I researched and decided to buy the Fuji Mini-Mite 3 T70. Thus far, It has been the best investment I made in equipment. Three things I would advise: 6 Ft. Flexible Whip Hose - Buy it! After reading other reviews, I am definitely glad I purchased the whip hose. It is much lighter and makes holding the spray gun a bit easier. Note: I have been spraying 17 ft trim boards outside and noticed that in the heat, the hose would separate from its coupling. This caused the gun to sputter paint all over my boards forcing me to stop, clean up the board and restart. I finally grabbed some zip ties to keep the whip hose attached to its fitting. Quick Connect Couplings: Completely worth having. It makes it so much easier to connect/disconnect the hose from the turbine when hot and moving things around. Wireless Remote - I bought a wireless remote for use with the sprayer so I didn't have to walk 20 feet back and forth to turn it on and off. It makes a difference when painting. I keep it in my pocket or on a hook in my spray booth so I can easily transition between tasks. Cleaning - Run a little mineral spirits through the gun after cleaning. It's an extra step that really helps keep it clean and lubricated. Also buy a longer bristled brush to get to the top of the paint feed tube. Carefully follow directions on how to clean the gun. Don't let paint sit overnight in your gun. The solids will settle and clean up is not fun. Painting - It took several passes and three coats to achieve the nice finish I wanted but I am very pleased with the results thus far. Definitely perform thin coats and build to your final. Although I haven't gotten to the cabinets yet, the baseboards and door casings have come out fantastic. Spray Problems - I had one issue with spraying. It was related to allowing paint to sit overnight in the cup. All of the solids settled and I couldn't stir the paint enough to keep it from clogging the filter. After stirring twice and a few failed passes, I replaced the filter and started over. Obviously, my error. Overall, this was a great investment for me. I'm sure there is comparable equipment and accessories out there, but if you are on the fence about the Fuji you won't regret it.

Scritto da: Kevin E.

Foam filters do a good job stopping any contaminants including overspray

Machine works as advertised. Must be kept away from the spray area so it does not ingest overspray. Foam filters do a good job stopping any contaminants including overspray. The only complaints are that it is quite noisy, definitely hearing protection recommended and the quick coupler between the hose and spray gun is quite easy to inadvertently disconnect with just a bump. It's nice that the gun is easy to disconnect but perhaps a bit too easy. I plan to change this. All in all a good machine for the price.

Scritto da: Amazon Customer

Very well made

Small, compact and powerfull turbine. I really enjoy using this HVLP. Thank you #fujispray

Scritto da: erik

Excelente máquina para pintar

Me.encanto la máquina de pintar fuji está hecha de buenos materias luego luego se siente la calidad del producto y deja unos acabados perfectos aún cuando no tiene uno experiencia en este ramo de la pintura .excelente la recomiendo mucho.