0
0

Total:€ 0.00

Ver carrinhoConfira
LoginRegister
0

Total:€ 0.00

Ver carrinhoConfira
LoginRegister

DROK® DC-DC4.5-30V a 0,8-30V Tensão constante e conversor de corrente Buck 12V a 5V 5A Placa do módulo regulador de tensão abaixador LED Driver Transformador de energia com luz de giro e controle PWM para painéis solares Auto Car

Brand:DROK

2.7/5

€
28.70

Recurso: Propriedades do módulo: módulo redutor não isolado (BUCK) Tensão de entrada: DC 4,5-30V Tensão de saída: DC 0,8-30V Faixa de corrente constante de saída: 0,1-5A Temperatura de operação: -40°c a +85°c Funcionamento frequência: 300KHz Faixa de frequência de controle PWM: 100-300Hz Eficiência de conversão: até 95% Proteção contra curto-circuito: SIM (a corrente limite é o valor de corrente constante de configuração) Proteção contra temperatura excessiva: Sim (temperatura excessiva desliga automaticamente a saída) Proteção de polaridade reversa de entrada: Nenhuma (instale o diodo na porta de entrada) Proteção anti-irrigação de saída: Nenhuma (siga a imagem para instalar o diodo anti-irrigação) Indicação de carregamento: carregando Luz vermelha, totalmente carregada Luz verde Instalação: quatro parafusos de 3 mm Fiação : Conexão: entrada V-IN, saída V-OUT Dimensões: 60x26x20mm Algumas aplicações: Regulador de tensão DIY, com corrente constante, pode proteger a carga. A fonte de alimentação para equipamentos eletrônicos. Para uma variedade de carregamento de bateria, ajuste a tensão de carregamento e corrente de carregamento de acordo com as diferentes tensões e capacidade da bateria, com indicador de carregamento, conveniente para observar o estado de carga. fonte de alimentação de painéis solares para carregamento de bateria, com corrente constante, o que evita a sobrecarga da bateria. LED de alta potência do driver, combinação série-paralela gratuita, com entrada de controle PWM, SCM disponível para controlar o brilho do LED (faixa de frequência de controle PWM 100-300Hz). Use como fonte de alimentação do carro, fonte de alimentação para equipamentos eletrônicos. O pacote inclui: 1x Conversor DC

Quantia
adicionar ao carrinhoComprar agora

EAN: 0619397028315

Categorias Ferramentas e Melhorias Domésticas, Industrial e Científico, Eletricidade, Dispositivos de automação residencial, Módulos,

Ampla aplicação: regulador de fonte de alimentação DIY; carregamento de dispositivos elétricos, bateria, painel solar; condução LED de alta potência, fonte de alimentação do carro. Possui indicador LED de corrente/carga/carga total constante, operação mais intuitiva e conveniente. Com dissipador de calor de alumínio, torna a temperatura do módulo que funciona em alta corrente por um longo prazo mais baixa e mais estável. Com proteção contra curto-circuito e superaquecimento, portanto, seguro para uso. Ampla faixa de tensão de entrada (DC4.5-30V) e tensão de saída (DC 0,8-30V, continuamente ajustável); Faixa de corrente constante de saída: 0,1-5A.
Brand DROK
Country of Origin China
Input Voltage 5 Volts
Is Discontinued By Manufacturer No
Item model number 090482
Manufacturer DROK
Output Voltage 5 Volts
Package Dimensions 5 x 5 x 1 inches; 1.6 Ounces

2.7

9 Review
5 Star
52
4 Star
19
3 Star
0
2 Star
0
1 Star
29

escreva sua revisão

O seu email não será publicado. Todos os campos obrigatórios são marcados com*

Scritto da: Chapman Flack
Know your application! This will not do constant-current (CC) if you have common negative
This is a well-made module that passed all tests on the bench and worked fine. Constant-voltage (CV), constant-current (CC) mode both work. But you have to know some details of where you will use it. One end of the board has two input terminals, IN+ and IN−. On the other end are two output terminals, OUT+ and OUT−. This board expects to supply your load between OUT+ and OUT−, and for the CC feature, it measures the current in the path between OUT− and IN− (that R010 resistor seen on the solder side appears to be the current-measuring shunt). What that means is if you use this device in a setting where IN− and OUT− are connected by any external path (say, both grounded to the body in a vehicle), this device will not see the amount of current flowing, and the CC feature will be useless. (I am glad I tested on the bench, and the power was coming from a supply that had its own current limit, which saved the day.) DROK's store shows a lot of similar modules, so I opened a question on their forum to ask if any of the other ones will work and do CC in a circuit with common negative. Sadly, their answer was "We are sorry so far there are no similare items can meet the requirement of common ground." Giving four stars because the module is fine for what it is, I can't fault it for having a certain limitation, but the description should have said so. Meanwhile, I used "Ask a Product Question" above, and so far it has only attracted one, wrong answer. After testing and checking with DROK, I know the right answer now, but I'm apparently not allowed to supply the right answer to my question. Could somebody who sees this and is not me please add the right answer to the question, so that isn't forever showing the wrong info?
Scritto da: Chicago John
Nice capabilities for the price
I got this to use along with an inexpensive 12VDC 10A power supply to limit current in high power LED's. While output constant current is limited to 0.1 - 5.0 amps, it should handle 5-6 10W LED's. After verifying that it works properly, I decided to add a DROK 0.28" DC 0-100V 10A Digital Current Tester Gauge Red Green Bright LED Display to facilitate setting voltage and current. Unless current adjustments are to be made infrequently, I think it's too cumbersome to put a meter in series with the load every time. That is no longer an issue with the DROK display I added. The resulting system works exactly as I'd hoped it would. The PWM capability is a feature that will be of use to me driving LED's. While instructions are sparse, I found that the key to using PWM is the "key" contact point. I soldered a male header to the three holes provided -- GND, PWM, and KEY, from left-to-right, respectively. If KEY is connected to GND, output power is cut. I would presume this may have been intended for use with an on-off switch. If PWM is grounded, however, no effect is seen. But when PWM and KEY are connected, power is cut. I tried using a 2N2222 transistor on one of the Arduino's PWM data pins with an analog write, and after using the "setPwmFrequency" to put the frequency within the necessary range of 100 - 300 Hz. For this I divided the native frequency 31250 of pin 11 by 128 to give a frequency of 244 Hz. Pin 11 was connected through a 1 kOhm resistor to the base of the transistor with PWM and KEY on the collector and emitter, and this seems to work for PWM dimming of the LED's, although I don't have a lot of experience with it yet. So while this system won't handle over about 60 watts, it should be fine for my current intended use. I'll update this review if I encounter negatives in either the buck supply or the DROK meter and display.
Scritto da: Justin Lloyd
Overall I am happy with the product
I use this to charge batteries with both my 30W solar panel and 15VDC power supply. Output voltage varies somewhat with input voltage. There is a few tenths of a volt change when I switch from my 15V supply to my 18V solar panel. This will not be a problem for most use cases. Voltage is steady when load changes but drifts up a bit when there's less than about 30ma being drawn. This could be important if you are using the voltage regulator to charge batteries. You could put a small fan or 1/2 watt resistor off the output side(before the diode) if this was a problem in your application. This variation is within the allowable range for most electronic circuits and would be acceptable for most people. You will need to place a diode on the + side of the output to protect the circuit from reverse voltage if the supply voltage ever dips below the voltage at the output terminals. Overall I am happy with the product. It is well made and is easily adjusted. It has no problem being enclosed in a very small space. I've run it for several hours at about 3 amps in an enclosure barely larger than the device and the heatsink only gets warm. Good for most projects requiring adjustable current and voltage.
Scritto da: T. Ogilvie
The Constant Current feature is working great, and allows me to adjust the LED's for ...
I am using this to power about about 10 LED under-eave lights on my home. The Constant Current feature is working great, and allows me to adjust the LED's for just the right current to have the level of light I want, while ensuring that I won't burn them out. My total current draw with all 10 units is less than 2amps at about 18VDC, and this unit is running very cool and reliably. I haven't been able to get the constant voltage feature to operate, not that I need that, but I tried it for fun. No matter how far I turn the potentiometer, I just get the same output voltage as the source power supply. Mine may be a bad unit, but the constant current side is working wonderfully, so I don't care much that the constant voltage side is non-functional. Overall I am happy with the unit, and have had it in operation for a couple of months now.
Scritto da: Practical Guy
Excellent module with a settable charge status green/red LED indicator.
What an excellent find this was! I'm working on a USB/solar/12v accessory chargeable super-capacitor flashlight and this module produces a great constant voltage and current. I did 3 different tests and feeding the input 12.8v DC from a car battery, 4.97v DC from a USB wall-wart and 5v from a small solar panel produced output at 2.6-2.7v DC on the once I had it set. The amperage I set to 2amps and it is also constant. The other nifty thing with this is that it has a green/red LED that can be set to a voltage. So I set that to 2.6v to match the output and once my super cap reaches that value the charge LED turns from red to green so you know its charged. This is a great feature on this module.
Scritto da: LASounD
Good product but a bit noisy
Works great! A little noisy under load but who cares;)
Scritto da: BlondieSL
These are the best of all the types I have.
I was using a different one for a project, but it was getting super hot, even with 2 heat sinks on it. I decided to use this one instead. At the same current draw and voltage, this one only gets slightly warm, as expected. I will order some more, very soon.
Scritto da: Amazon Customer
New as advertised. Quick Delivery. Works well.
New as advertised. Quick Delivery. Works well. Simple to use.
Scritto da: PPP
Perfect
Nice product with CC and CV function, So far works great!!!

Produtos relacionados

hot
Produtos de uso único, compatíveis com Alexa e Google Assistant, Homekit, Siri, E39-G8C Smart Hub, 1 pacote, branco 1 contagem (Pacote com 1) Homekit, Siri
2.9/5

€ 62.58

Produtos de uso único, compatíveis com Alexa e Google Assistant, Homekit, Siri, E39-G8C Smart Hub, 1 pacote, branco 1 contagem (Pacote com 1) Homekit, Siri
2.9/5

€ 62.58

hot
DROK® DC-DC4.5-30V a 0,8-30V Tensão constante e conversor de corrente Buck 12V a 5V 5A Placa do módulo regulador de tensão abaixador LED Driver Transformador de energia com luz de giro e controle PWM para painéis solares Auto Car
2.7/5

€ 28.70

DROK® DC-DC4.5-30V a 0,8-30V Tensão constante e conversor de corrente Buck 12V a 5V 5A Placa do módulo regulador de tensão abaixador LED Driver Transformador de energia com luz de giro e controle PWM para painéis solares Auto Car
2.7/5

€ 28.70

hot
Cabo de extensão de sensor Sense AEP5-ASSY 25, cabo de extensão cinza Sense 25'
3.9/5

€ 48.36

Cabo de extensão de sensor Sense AEP5-ASSY 25, cabo de extensão cinza Sense 25'
3.9/5

€ 48.36

hot
Módulo original Mopar 68067458AA
4.1/5

€ 718.16

Módulo original Mopar 68067458AA
4.1/5

€ 718.16

Conheça nossa rede internacional

Enviamos para 28 países, mais de 200.000 produtos. Fique atualizado, assine a newsletter.

Array

Total:€ 0.00

Ver carrinhoConfira

Categorias

Todas as categorias
Cardápio Categorias Aproximar Carrinho

Menu