Dispositivos de controle - CR25-100 -CR25 Série CR Válvula de alívio de pressão de latão, faixa de pressão ajustável de 0-100 psi, 1/4 macho NPT

Name: Dispositivos de controle - CR25-100 -CR25 Série CR Válvula de alívio de pressão de latão, faixa de pressão ajustável de 0-100 psi, 1/4 macho NPT
Brand: Control Devices
SKU: 0372657518635
Price: 40.30 EUR
Availability: InStock

Brand:Control Devices

3.6/5

€
40.30

Esta válvula de alívio de pressão CR25-100 da Control Devices tem um corpo de latão, uma pressão de alívio ajustável, uma conexão de entrada roscada NPT macho de 1/4 e um anel de vedação de fluorocarbono. O corpo de latão da válvula, a sede da válvula de latão e o gatilho de aço inoxidável resistem à corrosão e podem ser usados em temperaturas de operação de até 250 graus F. A válvula pode ser ajustada para abrir entre 0 e 100 psi usando o botão de náilon tipo micrômetro. Esta válvula de segurança tem uma taxa de fluxo padrão de 6 pés cúbicos por minuto (SCFM) e é adequada para aplicações de alívio de pressão de baixo fluxo, como em compressores de ar sem tanque. As válvulas de alívio removem o excesso de pressão ou vácuo de um sistema. As aberturas da válvula permitem que fluidos ou gases escapem para diminuir a pressão e, em seguida, fecham quando a válvula atinge o limite de pressão de reassentamento. Eles também aliviam o excesso de vácuo abrindo para liberar um gás no sistema e depois fechando após atingir seu limite de baixa pressão. Algumas válvulas de alívio possuem um mecanismo de ajuste para definir a pressão onde a válvula abre, tornando-a adequada para várias aplicações. As válvulas de alívio são classificadas de acordo com o volume de líquido ou gás que pode fluir através delas e o material com o qual a válvula é construída deve ser adequado para o fluido ou gás, que pode ser corrosivo ou em temperatura extrema, em que opera. As válvulas de alívio são usadas em uma variedade de aplicações, como compressores de ar, fabricação petroquímica e química, processamento de gás natural e geração de energia. A Control Devices fabrica válvulas e outros dispositivos de controle de fluxo. A empresa, fundada em 1963, está sediada em Fenton, MO.

Quantia

adicionar ao carrinho Comprar agora

EAN: 0372657518635

Categorias Industrial e Científico, Hidráulica, pneumática e encanamento, Acessórios, Válvulas, Válvulas de alívio,

Botão de nylon estilo micrômetro para ajuste de alívio de pressão. O anel de vedação de silicone fornece vedação à prova de vazamento dentro de 10 por cento da pressão de ajuste. Construção em latão e mola em aço inoxidável para resistência à corrosão. Conexão de entrada roscada NPT macho de 1/4. Pressão de alívio ajustável de 0 a 100 psi.

Brand	Control Devices
Country of Origin	USA
Domestic Shipping	Item can be shipped within U.S.
Exterior Finish	Stainless Steel
Inlet Connection Size	0.25 Inches
Inlet Connection Type	National Pipe Tapered
International Shipping	This item can be shipped to select countries outside of the U.S.
Is Discontinued By Manufacturer	No
Item model number	CR25-100
Manufacturer	Control Devices
Material	Brass
Outlet Connection Type	MNPT
Package Dimensions	4.33 x 3.23 x 1.69 inches; 2.4 Ounces

5 Star

4 Star

3 Star

2 Star

1 Star

escreva sua revisão

O seu email não será publicado. Todos os campos obrigatórios são marcados com^*

Sua avaliação

Scritto da: Mac

1 year of use and still good

I bought this to install on my steam sterilizer. The sterilizer reaches 121°C (250°F) and 15-18psi. I obviously have an additional safety release valve and a pressure gauge. The markings on the adjustable valve seem to be within the stated tolerance. It does occasionally get stuck closed. I learned it is best if I open it completely to vent before building pressure and then adjust it when the desired pressure is reached to allow very minimal venting. It never gets stuck if this is done. It always closes and does hold a vacuum upon cooling. All in all it does exactly what I want. I may replace it soon with the same valve simply because it is cheap and for peace of mind. 4/5 for overall quality 5/5 for quality at low price

Scritto da: Caitlin G

Good as a PRV

I’m using this PRV as part of a pressure fermentation and spunding rig. For my use it works really well with one exception. It needs to be used with a pressure gauge since the gauge on the pressure adjustment is 10-15 psi off. 10 psi on the PRV is actually 15 psi on a gauge.

Scritto da: Janice Villanueva

it works pretty cool so far for what I use it for

It relieves a fair amount of pressure. I believe more expensive valves relieve more pressure if that is what you need. Overall, it works pretty cool so far for what I use it for. Ignore the numbers used for measuring on this item. It's only there to make the item more attractive to buy. I had to buy a nut for mine in order to install it, which wasn't very hard. I use mine along with a pressure gauge on a homemade low pressure 55 gal steel sterilizing/pasteurizing drum. I never allow the tank to exceed 2 psi. I use this item basically to begin relieving pressure when the pressure reaches 1-1.5 psi. I adjust it according to my pressure gauge. It is most useful to me really in that it is an alarm for me to turn the propane down or open more wide the main relief valve. And I'm sure it helps prevent the psi from exceeding the point that it is set at. I do believe that if I turned the propane all the way up that this pressure relief valve would not be able to prevent my tank from exceeding the 2 psi that I am able to set it at. This is not a proven fact because I have not tested it. I'm just judging by the amount of pressure that this valve actually relieves. It relieves enough pressure that I don't try to find a better relief valve. But if I wanted to be perfectly safe i would wish for a valve that relieves more pressure so that to be sure that it would be impossible to exceed the 2 psi mark that I can set it at using this valve.

Scritto da: Book Lover

Seems to work great! I had it set at 75, and it didn't leak at 50PSI.

Seems to work great! I had it set at 75, and it didn't leak at 50PSI. The spring loaded design looks like this design should be fairly robust and fool proof. I heard that it leaked for some people, but my application didn't. I used thread tape and never opened it all the way up, so it seems to work for me.

Scritto da: D. Morrison

Leaking Valve FIXED

Like others, my PRV developed a leak out of nowhere (it would never fully close). I removed it from the fitting and found that a small piece of thread tape had become trapped in the valve seat, causing the leak. After removing this and reassembling, the leak is gone and the valve operates properly. I would be cautious using this in a setup where any debris could enter the valve. The markings are wildly wrong, but with a gauge in the system this is easily set to low pressure (10 PSI). I do not know if it would work toward the higher end of the rated range.

Scritto da: V. Williams

Tested positive for lead content

This device seems well made and durable, but if you are intending to attach it to a beverage line or passing liquid near it that is intended for consumption, think twice. Having read about various factories mixing lead in their brass, I decided to buy a reliable lead testing kit and tested all my recent brass connector purchases. Four out of 16 items tested positive for lead content. This item was one with lead in it. Photo provided with a sample of many items I tested.

Scritto da: David Swift

Excellent piece of hardware

Bought for a safety valve on a science project. Nice fine adjustment. Doesn't leak until set point is hit. Closes tight when pressure goes below set point. Tested with some pretty fast transients and it worked great. Could have done without the factory installed thread sealant.

Scritto da: Alex

Does the Job

I use it as an emergency air pressure release to bleed off back pressure from my Medo LA45C pump for my guppies LOL. Set it to open at 1.5 PSI I actually dump excess air through a ball valve and huge 1/5" x 8" airstones so my backpressure on the ball valve is set to 0.5PSI . but if airstones plug up this valve opens to keep back pressure from blowing my piston rings on the Medo.