Ventilador Tjernlund PS1505 com interruptor de bloqueio de segurança para ventiladores indutores de tiragem

Brand:Tjernlund

3.1/5

151.18

País de origem: Estados Unidos. O PS1505 não é compatível com válvulas de gás milivolt. Usado em conjunto com o Controle Universal UC1, garante a conformidade com os códigos e simplifica o intertravamento elétrico com todos os circuitos de queimadores de 24/115 VAC. O interruptor de teste do ventilador PS1505 monitora a pressão dentro da carcaça do indutor para verificar a operação do indutor.

País de origem: Estados Unidos. O PS1505 não é compatível com válvulas de gás milivolt. Usado em conjunto com o Controle Universal UC1, garante a conformidade com os códigos e simplifica o intertravamento elétrico com todos os circuitos de queimadores de 24/115 VAC. O interruptor de teste do ventilador PS1505 monitora a pressão dentro da carcaça do indutor para verificar a operação do indutor.
Brand Tjernlund
Item Dimensions LxWxH 6.5 x 6.4 x 6.6 inches
Number of Items 1
Operating Voltage 115 Volts
Operation Mode Mechanical,Electrical
Switch Type Pressure Switch
Unit Count 1.0 Count

3.1

2 Review
5 Star
76
4 Star
0
3 Star
0
2 Star
0
1 Star
24

escreva sua revisão

O seu email não será publicado. Todos os campos obrigatórios são marcados com*

Scritto da: Shmairsky
Ideal
Fixed a huge AC problem that could've cost me a fortune for just a couple of bucks and a YouTube video!
Scritto da: Dan T
No sensitivity adjustment, possible dangerous operating conditions with Tjernlund UC1 control
The review rating is for the lack of a sensitivity adjustment. The fan prover control, accessories and instructions are fine otherwise. If one of these is being installed in conjunction with an inline draft inducer, it interfaces with another control (Tjernlund UC1) that verifies whether or not the contacts on this switch are open. If the contacts on this control are closed, the main control thinks that the draft inducer is "on", and the control goes into lockout. The UC1 does not have a retry provision, only a setting to bypass the check to see if the draft prover contacts are open. The heat (or other connected appliance) is out until you notice a problem in this case and reset the UC1 control. If the inline draft inducer is connected to a furnace with a draft inducer, the furnace draft inducer may create enough pressure on its own to close the contacts on this fan prover switch. The problem here is that if the inline draft inducer stops functioning, the furnace draft inducer may be enough to keep the furnace operational, when it should shut down with the loss of the inline draft inducer. External (outside) winds may create enough air movement to close the contacts on this fan prover. This is the main problem I am having with my installation. I also experienced no furnace shutdown when I killed the power to the inline draft inducer (this is an important safety operational check). Both of these problems are mentioned in brief in the instructions for the UC1 control. The UC1 control has a provision to "turn off" the check for closed fan prover contacts. If activated, the connected appliances may continue to operate even if the inline draft inducer does not. In my opinion, this is a serious design flaw with the UC1 control used in combination with the recommended fan proving switch. The only appliance type that will shut down in any of the above scenarios would be natural draft and have a thermal safety switch on a barometric damper or draft hood, like a water heater or standard boiler. Tjernlund supplies what they cal a "linear limit switch" for these installations. I will have to source an adjustable pressure switch from another manufacturer to prevent these issues.

Produtos relacionados

hot
hot
JOMAR TWV-3W-T-KIT 810-504G
4.1/5

€ 205.84

JOMAR TWV-3W-T-KIT 810-504G
4.1/5

€ 205.84

Conheça nossa rede internacional

Enviamos para 28 países, mais de 200.000 produtos. Fique atualizado, assine a newsletter.

Array