Estação de trabalho portátil Rockwell RK9002 JawHorse Sheetmaster

Brand:Rockwell

3.7/5

€
933.02

DESCRIÇÃO DO PRODUTO O JawHorse Sheetmaster resistente é assim chamado porque pode suportar uma folha inteira de compensado de 8 x 4 por si só. Não há necessidade de chamar um vizinho para ajudá-lo a realizar um projeto quando você tem o JawHorse. Mantenha suas mãos livres para usar suas ferramentas em vez de usá-las apenas para apoiar seu trabalho. E eleve seu projeto do chão até uma altura de trabalho confortável. O Sheetmaster é realmente um 3 em 1, pois possui funcionalidade de bancada, torno e prensa de máquina. É forte o suficiente para dobrar ou endireitar metais, feito de aço sólido com 10x a força de aperto de um torno padrão e possui o poder de prensagem industrial de uma prensa mecânica de uma tonelada. São 53 libras, o que é substancial, mas precisa suportar projetos de 600 libras com 1 tonelada de pressão de fixação. Mas foi projetado com uma série de recursos para facilitar o uso. A perna traseira funciona como uma alça e as pernas dianteiras têm rodas destraváveis, para que você possa levantar a parte traseira e empurrá-la pelo local de trabalho como um carrinho de mão. Além disso, o pedal faz grande parte do trabalho de fixação para você, deixando suas mãos realmente livres. É 39" x 39" x 34" quando em pé e 29" x 14" x 13" quando dobrado. porque estão confiantes no desempenho de suas ferramentas. AMAZON.COM O Rockwell RK9002 JawHorse Sheetmaster é a única estação de trabalho de que você precisa, graças à sua força de fixação de mais de uma tonelada, construção sólida em aço, design dobrável portátil e pedal para fixação e trabalho sem as mãos. Para conveniência adicional, seu interruptor de liberação de bloqueio permite que você bloqueie o material - como uma folha inteira de madeira compensada - no lugar e libere-o facilmente com o toque de um botão, tornando o JawHorse Sheetmaster uma adição conveniente e confiável para a oficina ou trabalho. site.RK9002 JawHorseSheetmaster Visão geral: * Segure folhas de até 48 polegadas em uma ferramenta com força de fixação mãos-livres * Dobre rapidamente para um portátil de 43 libras com rodas em linha reta integradas para facilitar a portabilidade * Dimensões: 39 polegadas por 39 polegadas por 34 polegadas em pé; 29 polegadas por 14 polegadas por 13 polegadas dobradas * Apoiado por uma garantia limitada de cinco anosO Rockwell JawHorse Sheetmaster pode funcionar como uma bancada de trabalho, um torno e uma prensa de máquina (ver maior). isto. As poderosas mandíbulas de fixação do JawHorse Sheetmaster permitem que você prenda com segurança praticamente qualquer coisa, para que você tenha acesso sem as mãos para concluir seu projeto com segurança. Você pode até prender itens largos, como portas ou folhas inteiras de compensado, graças à largura de fixação de 49 polegadas. Basta configurá-lo, travá-lo e prendê-lo. Versátil WorkbenchGraças ao seu design flexível, o JawHorse permite que você levante seus projetos do chão em uma altura de trabalho confortável. Simplesmente prenda um pedaço comum de madeira compensada no JawHorse e você terá uma bancada de trabalho perfeita. Você pode até usá-lo no local de trabalho como uma plataforma robusta para serras de esquadria, serras para ladrilhos e muito mais. Além disso, a base do tripé oferece estabilidade excepcional em todos os terrenos - e as pernas dianteiras incorporam orifícios para permitir a fixação para trabalhos mais permanentes. Torno e prensa de máquina Quer você esteja dobrando metal ou endireitando-o, a força e a estabilidade do JawHorse Sheetmaster permitem que você seja agressivo com o seu trabalho. O JawHorse Sheetmaster é feito de aço sólido e tem 10 vezes o poder de fixação de um torno normal. Ele também apresenta o poder de prensagem industrial de uma prensa mecânica de uma tonelada. . DO FABRICANTE Agora você pode apoiar e prender uma folha inteira de compensado 8x4 com apenas uma ferramenta. O Rockwell RK9002 JawHorse Sheetmaster é o melhor ajudante de local de trabalho. Sua operação mãos-livres facilita prender e segurar suas peças de trabalho. Deixe o Sheetmaster fazer todo o suporte e estabilização para você, permitindo o uso livre de suas mãos para suas ferramentas, em vez de usar suas mãos para estabilizar seu trabalho. As garras que não estragam as garras ajudam a proteger seu trabalho. O Sheetmaster é resistente e suporta até 600 lbs. de peso com até 1 tonelada de força de aperto. Quando terminar, dobre-o para armazenamento compacto ou para facilitar o transporte. O Rockwell Sheetmaster tem rodas de scooter para rolar facilmente de e para o local de trabalho. A perna traseira funciona como alça para facilitar ainda mais o transporte. Com o Sheetmaster Rockwell JawHorse, basta configurá-lo, bloqueá-lo e prendê-lo para suporte de mãos livres para seus projetos. Ver mais

Quantia

adicionar ao carrinho Comprar agora

EAN: 787721480389

Categorias Ferramentas e Melhorias Domésticas, Ferramentas elétricas e manuais, Peças e acessórios para ferramentas elétricas, Suportes e bases móveis, Stands,

[FÁCIL DE MOVER] Fácil de guardar. Com travas de perna de liberação rápida, o JawHorse se dobra rapidamente e as rodas destraváveis facilitam o empurrão. [BASE DO TRIPÉ] Três pernas perfeitamente posicionadas fornecem mais suporte em terreno irregular do que quatro pernas. [NO MAR PADS] Feito de uretano para que eles agarrem o material sem deixar marcas, perfeitos para projetos de marcenaria premium. [1 TONELADA DE FORÇA DE APERTO] 2.000 lbs de pressão significa que o projeto não vai a lugar nenhum e, com uma carga máxima de 600 lbs, ele aguenta muito. [SEGURA UMA FOLHA COMPLETA DE MADEIRA COMPENSADA] Com até 49" de faixa de fixação e um método de fixação de 3/8" por passo. [TODA A CONSTRUÇÃO DE AÇO] Construído para durar e construído para manter seus projetos mais importantes enquanto suas mãos ficam livres para usar suas ferramentas.

Batteries Included?	‎No
Batteries Required?	‎No
Color	‎Black
Customer Reviews	4.7 4.7 out of 5 stars 780 ratings 4.7 out of 5 stars
Is Discontinued By Manufacturer	‎No
Item model number	‎RK9002
Item Package Quantity	‎1
Item Weight	‎27 pounds
Manufacturer	‎Rockwell
Part Number	‎RK9002
Product Dimensions	‎17.9 x 39.8 x 15.9 inches
Warranty Description	‎Limited 2-year

5 Star

4 Star

3 Star

2 Star

1 Star

escreva sua revisão

O seu email não será publicado. Todos os campos obrigatórios são marcados com^*

Sua avaliação

Scritto da: WatchItBurn

Not cheap

Not cheap but it's certainly not cheap. Yeah, It costs what I make in a day but damn it's built like it costs what I make in a day to make. Solid tool, holds small engine blocks, painting projects, welding projects, glue ups and I'm pretty sure with the right accessory, it'll hold up a rocky marriage, or hold back a zombie horde. We've all heard of generational wealth, I don't have any of that but I'll tell you what, This here is a generational tool. Ur kids'll be using this to hold what's left of the American dream together long after you're gone. Hell, if theres anything that can hold whats left of ol US of A together, it'd be this tool right here. Thank you Rockwell. Other brand simply can't hold a torch to you.

Scritto da: Andrew Czop

Great tool!

I have never owned a jawhorse before, and decided to get this newer model, the sheetmaster, instead of the original. It was a little more money, but the added features and ability to handle 48" wide sheets without buying additional adapters was a bonus. It is my understanding that this version is a little beefed up from the original, has the 48" capacity out of the box, has a different wheel/rolling system, and is easier to break down. I wanted a jawhorse to basically use as a portable vise. To hold material securely when cutting off 2x material, to hold larger items while sanding, chiseling, or ripping, etc. I was sick of working on the ground, or inconveniently on saw horses, etc. Since I got it, I've also used it as a miter saw stand, which worked great. I watched and read a lot of reviews, and determined that even though this unit is expensive, it would be worth it to me, and it definitely is. It is super easy to set up and break down. It takes maybe 30 seconds to unfold a few legs and flip it over, and vice versa. The clamping force is great. I haven't tried to measure it, but it is definitely more than enough to secure whatever you put into it. The jawhorse is not really prone to tipping due to it's design, but obviously can if you force it, and I say this to say that from my off the cuff tests, I get the unit to tip before I can dislodge/slip the material that is locked in the jaws. This is to say, the clamping force is fantastic. And super easy to clamp something by allowing you to use your foot, which frees up both hands to make sure the piece is placed just the way you want it. I have yet to put a full sheet of anything into the jaws. It comes with an extra jig piece that quickly clamps and holds holds two pieces of 2x material at 90 degrees that is meant to be additional support for full sheets. The two pieces at 90 degrees form an "L" where the mid point of the long side of the "L" rests on the jawhorse to support the long dimension of the sheet, and the short side of the "L" rests on the ground. It looks to be pretty quick to set up, but you'd have to have that 2x material handy whenever you plan to do full sheets (maybe not as travel friendly then), and would have to set up the clamps each time. And then you wouldn't want to lose the clamp jig, and it does not store with the unit itself. This is all to say that yes it does full sheets, and I'm sure it is great at it, but it's not a fully integrated solution that all packs away into the unit itself. If you're going to be cutting a number of sheets, it's definitely worth it to set up the extra jig and go to town, but otherwise, you'll probably not be using it for single sheet cuts. This doesn't mean that the 48" jaw capacity is not useful though, beacause there are still times where you may want to hold something "long ways" by its <48" dimension, and as long as it's not wider than a few feet, you wouldn't need the support braces. One gripe I have about the unit, the only one so far (unless you count how cumbersome I view the support brace setup to be), is that when you try to wheel it, (a neat feature by the way, that you can compact it, and it wheels with the leg as a handle), a combination of the wheels being small and close together results in a lot of rocking while wheeling. You wind up fighting it while wheeling it, even on flat ground to an extent. Like a crappy suitcase where it's constantly on one wheel, then the other, then the other, back and forth, etc. You have to baby it to get it to roll properly, even on flat ground. If you are trying to do stairs, or go over grass or anything else, forget it. I personally have about given up on the wheels and just carry it. If you're going 10 or 20 feet across the garage, the wheels are OK, but more than that, it saves time and frustration to just carry it. My understanding is that the two wheel design this unit has is different than the single roller the original jawhorse has, and is supposed to be better. I haven't used the original, so I don't know how that one works, but I can say that I am not too impressed by the wheeling capability of this unit. It's fine for flat ground, and I guess not *too* bad overall. Let me say this... it's better than not having them, so there's that. But I do think they could be improved. One other note is that you need to be careful with the clamping force. It's hard to control just how much you use, and when removing it, just like an E-brake on a car, you need to apply *just* a little more force than you used to clamp/lock it, which means a little more clamping force needs to be applied to remove a clamped item. You wouldn't want to use it to hold anything delicate. For example, I tried a test piece of 1/2" copper pipe, and found that it was difficult to secure the pipe without crushing it out of round. Even when I got it to hold without hurting it too much, it was far too easy to press too hard on the foot pedal when releasing it and just smash the copper flat. You don't realize how much clamping force it really has until you see this and how easy it is to do. It's one thing to clamp things in a normal bench vise where it closes slowly, turn by turn by hand, but with the jawhorse where you use your foot and a lot of clamping force is applied very quickly for what feels like not pressing very hard with your foot, it can be a problem for these delicate items. This is awesome when grabbing wood and items that aren't easily crushed, but it does mean that you want to be careful with anything that you would be weary about in a normal vise. I would remove a star because of the wheels, but it's not a key enough feature to me to do that. It really is a 5 star item IMO. Extremely well made, performs its functions extremely well, and is just a down right awesome tool. I love it.

Scritto da: PhotoKing

A very useful tool

I had trouble deciding if this was a 5 or a 4 star product. Pro's: Very sturdy, holds a full sheet of plywood, fairly portable Con's: Clumsy to roll and carry, tripping hazard, comes with silly looking wood holder, very hard to remove yellow part, see below for rest. Overall I like the tool, it's my new favorite thing. Long gone are the days of having to clamp a piece of wood to my bench to cut with a recip or scroll saw. To cut odd shaped things I would have to drag my tools outside. Now inside I can set it up, open, clamp and work. Clamp a piece of wood in the jaws and place a small table saw, or make it into a bench. The jaws have removable rubber covers. However all that said the things I don't like are a few. For one, after you unfold it, it's hard to pick up and really awkward. While 50 pounds isn't super heavy, it isn't light. And I hurt my back a few times. When folded you have to make sure you fold it in the right order, folding the legs down first so it folds tighter. It can fold other ways that are less tight. This things is awkward to carry. It doesn't roll well, it's very tipsy. Rolling it up stairs is a good way to dislocated a shoulder. Carrying it is even harder, I wish there was an easy way to carry this upright. If you clamp a pipe, you will flatten the pipe. There is no pipe holder, there are some V ridges, but it would be nice to have. The yellow sled is designed to come out and reverse. But it's so well engineered that the paint makes it very tight to remove, it's a tug of war to that thing out each time. I found oiling the bearings holding it in helps. Greasing the rails made a mess. There is no fine clamping force, the clamp is designed to sort of walk the yellow sled forward and it moves it in 1/2" increments. So if you want to compress something like a spring, or maybe even crush a can - you may have a hard time if it's pushing back. I found that the foot pedal a little too high, and you have to remember to lock and unlock the thing each time you want to clamp or unclamp. Unfolded it's very stable, but for whatever reason I seem to trip over one of the legs every single time I pass by. I don't think that's a design flaw, yet something about that design I keep tripping over it. It comes with a little device that you attach to a piece of wood and it creates a sort of foot to hold up large boards. But as nice as it is, there is no place to put it. It can't fit on the horse, and it's so easy to lose.

Scritto da: Manuel M.

Einfach nur genial!

Servus zusammen, ich weiß überhaupt nicht warum dieses Gerät oder besser die Art, hier in Mitteleuropa fast gänzlich unbekannt ist. Ich bin durch einen Megazufall darauf gestoßen. In einem Beitrag von April Wilkerson dachte ich mir, WTF, was ist das da? In der Liste Ihrer Werkzeuge stand dann JawHorse. Was zum Teufel ist ein JawHorse!?! Ich kann sagen, ein einfaches und wirklich geniales Teil. Ich habe darauf geachtet dass ich Werkstücke von mehr als 1200mm einspannen konnte, ja und Zack, da habe ich mir das Dingens hier bestellt. Egal was, drauflegen, einspannen (der Druck ist hervorragend einstellbar- ich spanne u.a. 10mm Gipsfaserplatten ein) und loslegen. Der Stand des Bocks inkl. des Materials ist einfach Mega! Fazit: Jeder der Plattenwerkstoffe oder Türen bzw. Fenster aufarbeitet bzw. bearbeitet sollte sich sowas hier anschaffen! Wenn möglich noch mehr Sterne! Vielen Dank an April! Beste Grüße

Scritto da: HOOCH 463

Rockwell Jaw Horse

Arrived very promptly impressed with the delivery service. As mentioned in other reviews it is a little on the heavy side, but this is due to the outstanding construction. It truly is built to last. Typical man I didnt bother with the instructions to put it up and took a while to figure it out. It requires turning on its back and getting the legs and clamp system opened in the correct order. If you have a back injury or mobility issues this is not something you will want to be putting up and down on a regular basis. But the footprint isnt too large so could be left up for the home DIY ehthusiast with enough space. Folding it up requires it to be flipped over again and I have noticed that when you do start to turn it over, and put pressure on any of the legs to act as the pivot, they are prone to start to fold up. It is essential that all safety clips are checked to be firmly seated before you start to roll it over. Due to its weight and shape it will soon trap your hand or collapse in a heap if you dont follow the instructions carefully. But it does exactly what it says on the box. 10/10 for design and construction very impressed indeed.

Scritto da: Frank

it folds and stores easily but is extremely sturdy and strong when in use ...

I purchased this product with the expectations of it being a mid quality tool. It is anything but. I am very impressed with the quality of workmanship and design. I wanted the capability to handle full sheets of plywood but did not want a bench that would forever be in the way when not in use. it folds and stores easily but is extremely sturdy and strong when in use (not something I'd expect from something with folding legs). Lastly the foot controls are genious as it frees up both hands for larger objects.

Scritto da: John Aflack

Solo Mate

The Rockwell RK9002 48-Inch JawHorse Sheetmaster is the ideal partner for the solo handyman. It extends to hold a 4x8 ft. plywood sheet, and comes with a clamp to extend the support surface using 2 by 4's. It is robust and is not made out of cheap stamped metal. The 3-legged system prevents tipping. In addition it can be easily folded up and comes equipped with built-in wheels. It is worth the investment. There are accessories available for clamping chainsaws, mitre saws and rollers. You won't be disappointed with this as your work project partner!

Scritto da: Dallas from E-Town

Really solid grip.

Big enough to hold larger work pieces without tipping over. Grips well.