0
0

Total:€ 0.00

Ver carrinhoConfira
LoginRegister
0

Total:€ 0.00

Ver carrinhoConfira
LoginRegister

CHAVE DE ENGRENAGEM 114 Pç. Conjunto de machos e matrizes com catraca SAE/métrica - 82812 114 Conjunto de PC

Brand:GEARWRENCH

3.8/5

€
452.63

DESCRIÇÃO DO PRODUTO Este conjunto completo de machos e matrizes GEARWRENCH padrão e métrico SAE é perfeito para o mecânico mestre ou oficina mecânica que possui uma ampla variedade de necessidades de rosqueamento. 48 machos e 48 matrizes fornecem qualquer tamanho necessário, e nossas ferramentas são projetadas desde o início para trazer inovações GEARWRENCH para nossos usuários que trabalham duro, como a cabeça de 5 catracas de nossas alças T ou o sistema de guia patenteado Twist Lock que protege qualquer extensão ou ferramenta de corte ao cabo, produzindo roscas retas em cada corte. AMAZON.COM Conjunto completo de sistema de manípulo em T de catraca para ferramentas de macho e punção (visão maior). reduz o retrocesso da guia da matriz e mantém as matrizes centralizadas durante o corte das roscas. A chave T de catraca fornece um arco de catraca de 5 graus e sua alavanca reversível permite mudanças rápidas de frente para trás para eliminar o giro manual. O QUE ESTÁ NA CAIXA 82800 chave T de catraca grande, 82801 adaptador de torneira de travamento grande, 82802 adaptador de matriz hexagonal grande, 3881 chave T de catraca média, 3883, adaptador de torneira média, 3882 adaptador de torneira pequena, 3884 adaptador de matriz média, 82803 adaptador de extensão macho, 82804 fêmea adaptador de extensão, T deslizante para adaptadores, chave hexagonal de 4 mm, 5 extratores de parafusos, medidor de rosca métrica, medidor de rosca SAE, 48 machos e 48 matrizes SOBRE A GEARWRENCH soquetes, chaves de fenda/porca, alicates e ferramentas especiais. Não importa o setor em que você se encontra, a GearWrench tem as ferramentas para atender às suas necessidades - desde as precisas até as quase indestrutíveis. As ferramentas manuais da GearWrench têm garantia vitalícia contra defeitos de material e mão-de-obra. * A alavanca reversível elimina o giro manual * Construção em aço carbono * Garantia vitalícia DO FABRICANTE Chave de engrenagens Torneira de catraca grande de 114 peças e conjunto dietético SAE/métrico, consistindo de: chave em T de catraca grande 82800, adaptador de torneira de travamento grande 82801, 82802 grande adaptador de molde hexagonal, 3881 chave T de catraca média, 3883, adaptador de macho médio, adaptador de macho pequeno 3882, adaptador de molde médio 3884, adaptador de extensão macho 82803, adaptador de extensão fêmea 82804, T deslizante para adaptadores, chave sextavada de 4 mm, extratores de parafusos 5, métrico calibrador de rosca, calibrador de rosca SAE, 48 machos e 48 matrizes. Conjunto completo de 48 machos e 48 matrizes, além de sistemas pequenos, médios e grandes de alças T de catraca, adaptadores de torneira de travamento e adaptadores de matriz hexagonal. Machos e matrizes são feitos de aço carbono para ferramentas de alta qualidade. Os sistemas de catraca de chaves de engrenagem - I são perfeitos para o mestre Mecânico ou Oficina de Máquinas. Conjunto vem com estojo moldado por sopro para armazenamento seguro e organizado. Ver mais

Nenhuma unidade disponível

EAN: 787721817901

Categorias Ferramentas e Melhorias Domésticas, Ferramentas elétricas e manuais, Ferramentas manuais, Tornos e matrizes, Conjuntos de tampas e matrizes,

Os adaptadores de extensão de unidade fornecem maior acesso em áreas confinadas quando usados ​​com extensões de unidade de 3/8 polegadas. O recurso de travamento automático permite que os adaptadores de torneira sejam removidos com segurança Estojo para transporte do molde de sopro com suportes de torneira inclinados para fácil acesso e armazenamento O conjunto inclui 2 alças T de catraca, 3 tamanhos de adaptadores de torneira e 2 tamanhos de adaptador de matriz, 2 adaptadores de extensão e um T deslizante para os adaptadores, uma chave hexagonal de 4 mm, 5 extratores de parafusos, medidores de rosca SAE e métricos e 48 machos e matrizes em tamanhos SAE e métricos variando de 4 40 a 3/4” e 3 mm a 18 mm. Os adaptadores de matriz funcionam com o sistema de catraca e soquete de passagem de acionamento de 3/8 polegadas, bem como acessórios de soquete. A chave de catraca t funciona com o sistema de passagem GEARWRENCH através do soquete. O sistema de guia de trava de torção reduz o “caminho para trás” da guia da matriz e mantém as matrizes centralizadas durante o corte. A catraca lida com matrizes de vento com um arco de giro de 5° e possui uma alavanca de reversão para eliminar o giro manual.
Batteries Included? ‎No
Batteries Required? ‎No
Color ‎As Shown in the Picture
Country of Origin ‎Mexico
Customer Reviews 4.7 4.7 out of 5 stars 3,959 ratings 4.7 out of 5 stars
Domestic Shipping Item can be shipped within U.S.
Finish ‎Full Polish Chrome; taps & die are untreated
Included Components ‎
International Shipping This item can be shipped to select countries outside of the U.S. Learn More
Is Discontinued By Manufacturer ‎No
Item model number ‎82812
Item Package Quantity ‎1
Item Weight ‎1.3 pounds
Manufacturer ‎GearWrench
Material ‎Steel
Measurement System ‎SAE & Metric
Part Number ‎82812
Power Source ‎Hand Powered
Product Dimensions ‎21 x 13 x 3 inches
Shape ‎Rectangular
Size ‎114 PC
Style ‎Set
Usage ‎Professional
Warranty Description ‎No Warranty - Consumable

3.8

13 Review
5 Star
82
4 Star
12
3 Star
3
2 Star
1
1 Star
2

escreva sua revisão

O seu email não será publicado. Todos os campos obrigatórios são marcados com*

Scritto da: OZ4
Works Great
Works as advertised!
Scritto da: nick radakovich
Value
Where I work taps are important an the quality is a must
Scritto da: Kenn
6 years and counting
Had these for six years and use them all the time as I restore a classic beetle to chase threads and other small projects. It’s a great set. The ratcheting handles are great, it’s all of great quality. Love this set.
Scritto da: Whilly whips
Worked great
Worked great as expected!
Scritto da: Tex
A great set with a lot to offer for this home-user.
I had read the reviews here before purchasing and especially took note of the people that reported some gouges in some of the machined taps with this set. I ordered anyway for a couple of reasons. First, this is no small company. It is part of Apex Tools that owns Lufkin Tapes, Crescent Tools, Wiss cutting tools, Nicholson Files and more etc that go back over 100 years. I have all of those tool Brands at home and they have served me exceptionally well for 30-40 years. So, I figured I'd give this set a go and if it was totally unacceptable, I could always return it (thanks to Amazon's service). Bottom-line, its not going back... I'm a home/hobbyist user of Tap and Dies, but I can understand why a Professional who uses these tools in a daily business setting can feel differently about what they need. But for my use at home, this is a great set, and for what you get, a very good price. I could not touch an equally configured Irwin/Hansen set for this price point. I have also used this set and it does a very acceptable job for my needs. Regarding the reports of the small gouges in some of the larger Taps, yes I have those too. But it is only on a couple of the Taps, the gouges are small, and the gouges are not on the cutting edges of the Taps. The cutting edges are clean, in tact and sharp. The very few gouges are on the threaded following surfaces, so that problem (for me) will not affect the tool's ability to cut proper threads. I did find that I needed to clean out a few loosely attached burrs from a couple of the Taps when they were machined. A small brass brush or even the "thread gauges" that come with this set easily dispatched those burrs. I have already used some of the Taps and they cut very well. The accessories that come with this set are quite remarkable and they work well too. I especially like the Tap Adapters that come with this set and they way they lock into the T-wrenches. My only complaint about the T-wrenches is that I can't lock the ratchet into place. You either go forward or backward via the selector flip/switch. If you have done much tapping of harder metals, you know that going forward and back quite often is needed to dislodge the burrs that you cut. I can accomplish it with the flip-lever, it would just be easier (at times) if the T-wrench didn't ratchet. But for cutting soft metal, I love that ratchet and the ability to move the handle without changing my grip is very appreciated. Overall, I think this set is a winner. I understand that it is not an Irwin/Hansen or even higher quality set. But for my use, that is OK and I expect to get many years of use from this set. I already have a much smaller, very cheap quality Tap and Die set that I've owned for 30+ years. Take care of your tools, use some finesse vs brute force, use cutting fluid, etc. and you can get many years even from a lesser quality Tap and Die set. :^) One update (4/23/16): I also purchased the Gator Tools V-Tap Guides that help keep the tap vertical (especially when starting the threads). The Gator Tools Tap Guide is a well made/machined part that earns a full 5-stars all by itself. Unfortunately, for this particular Tap set from GearWrench, on their smaller Taps (the Metric M5 and smaller) and (the Standard #10 and smaller), these Taps will not pass through the Big Gator Tools Tap Guide. That is because GearWrench makes the barrel (above the cutting portion of the Tap) slightly larger. Because of that design on their smaller Taps, it prevents the Tap from passing through the Big Gator Tape Guide. I've looked at these sizes in the Irwin Taps and it appears that Irwin maintains the barrel diameter so that it is not larger than the cutting portion diameter of the Tap. If something like this is important to you, then it may be worth considering Irwin vs GearWrench. I'm still happy with my GearWrench set and have some older Taps that will pass through the Big Gator tool just fine. Just thought I'd mention it as a difference for those considering this GearWrench set.
Scritto da: 338 Lapua Shooter
Good kit and good value
I purchased this kit about 5 years ago because I didn’t want to bring my snap on tap and die set to my shop where they would surely get lost or stolen by my staff. I didn’t have exceedingly high expectations of the kit but to be honest it’s just as good. As with any set you need to use a light cutting oil and as such I always use a thin oil. Over the years I have broken many bits and pieces of these types of kits, even my snap on ones and they always replace them…. But I have yet to break one of these. When I got my snap on brand products I was in the aftermarket automotive industry so I used them on a more routine basis, but now shifting careers to firearms I use different thread patterns and mostly the smaller ones which are far more prone to break, but these never have broken. To be entirely honest I paid almost half the price that they currently are selling for right now and since they’ve worked so well for me I’d have zero hesitation to buy a new set should I need them. The “big truck” brands I don’t think are any better and surely not worth the inflated cost which is likely 3-5 times as much as this kit. You’ll be happy with the kit.
Scritto da: Dexter See
Very good
Very good
Scritto da: Dustie Rose
High quality at a cheap price
For $210 I am extatic. This 114pc set performs just as good as my Snap-On set that has only HALF of the contents as this 114pc set and is twice the price. The ratcheting tap handles are elite, definitely a game changer when it comes to tight spots. Overall, I am very impressed with how these tap and die perform on both mild, stainless, and even aluminum. I would highly recommend this set to anyone.
Scritto da: ali
Very good
Great quality, love the ratchet
Scritto da: Laurence
Would love a refund or replacement
There seems a lot of play in the ratchet mechanism, and the ratchet direction lever has little resistance so when your removing the tap quickly the ratchet leaver keeps changing direction on its own account, this is extremely annoying,
Scritto da: Aivaras Ceida
Useless thing
Complete peace off ... Second time i used it and the centre ratchet mechanism fell out and i lost pressure spring
Scritto da: Mixx Cheang
Amazing!!
Very sharp and precise, bought a set of lang and did not fix a cross tread bolt almost snap the tool. Return it and bought gw tap and die set and work perfectly. Very happy with that tool safe a lot of time with the right tools.
Scritto da: MECANO
MECANO
bonjour l'outil est bien fait pour les endroit étroit merci.

Produtos relacionados

hot
IRWIN Tools Tap and Die Set, Performance Threading System, Deluxe, 116-Piece (1813817)
3.7/5

€ 801.79

IRWIN Tools Tap and Die Set, Performance Threading System, Deluxe, 116-Piece (1813817)
3.7/5

€ 801.79

hot
Conjunto de machos e matrizes VEVOR, com estojo de armazenamento, conjunto grande de machos e matrizes para cortar roscas externas e internas (60 unidades)
3.2/5

€ 84.00

Conjunto de machos e matrizes VEVOR, com estojo de armazenamento, conjunto grande de machos e matrizes para cortar roscas externas e internas (60 unidades)
3.2/5

€ 84.00

hot
Irwin 8338 10mm x 1,0 Tamanho da torneira métrica: 10MM-1,0mm.
3.8/5

€ 26.28

Irwin 8338 10mm x 1,0 Tamanho da torneira métrica: 10MM-1,0mm.
3.8/5

€ 26.28

hot
DEWALT 1/4 1/2 pol Ajustar alça TAP
1.5/5

€ 56.89

DEWALT 1/4 1/2 pol Ajustar alça TAP
1.5/5

€ 56.89

hot
Irwin 80213 #6x32 Conjunto de furadeira/torcedor NC
3.5/5

€ 26.38

Irwin 80213 #6x32 Conjunto de furadeira/torcedor NC
3.5/5

€ 26.38

hot
Matrizes de tubos RIDGID 38120 para rosqueadores de engrenagens recuadas, matrizes de tubos NPT de alta velocidade para destros com tamanho nominal de tubo de 2-1/2 polegadas a 4 polegadas para rosqueadores de tubos com engrenagem 141
4.1/5

€ 567.82

Matrizes de tubos RIDGID 38120 para rosqueadores de engrenagens recuadas, matrizes de tubos NPT de alta velocidade para destros com tamanho nominal de tubo de 2-1/2 polegadas a 4 polegadas para rosqueadores de tubos com engrenagem 141
4.1/5

€ 567.82

hot
Eazypower 82544 1-1/8-12 Nf Plug Tap (1 pacote)
3.6/5

€ 89.32

Eazypower 82544 1-1/8-12 Nf Plug Tap (1 pacote)
3.6/5

€ 89.32

hot
Chaves de torneira em T IRWIN Hanson 12002, 1/4 - 1/2
3.4/5

€ 31.79

Chaves de torneira em T IRWIN Hanson 12002, 1/4 - 1/2
3.4/5

€ 31.79

Conheça nossa rede internacional

Enviamos para 28 países, mais de 200.000 produtos. Fique atualizado, assine a newsletter.

Array

Total:€ 0.00

Ver carrinhoConfira

Categorias

Todas as categorias
Cardápio Categorias Aproximar Carrinho

Menu