Engate do receptor dianteiro CURT 31075 de 2 polegadas, selecione Toyota Tacoma

Brand:CURT

3.6/5

500.42

Um engate de reboque frontal CURT permite que você use a extremidade dianteira do seu veículo para uma variedade de aplicações de reboque. Eles podem ser usados ​​para montar um guincho, um arado de neve, uma série de acessórios de reboque e podem até ser usados ​​para algumas aplicações de reboque. Quando o espaço é limitado, um engate de reboque dianteiro é comumente usado para segurar um transportador de carga, liberando espaço dentro do veículo para carga extra e disponibilizando o receptor de montagem traseira para puxar um reboque. Na rampa do barco, o reboque do barco pode ser engatado ao engate do receptor dianteiro, dando a você melhor controle sobre o reboque durante o lançamento. Alguns dos outros acessórios que podem ser usados ​​com um engate de reboque dianteiro são o suporte de guincho CURT, degrau, porta-placa, suporte para pneu sobressalente, protetor antiderrapante e ganchos de reboque. Todos os engates de reboque dianteiros CURT fornecem um tubo receptor útil para aceitar uma haste de 2 x 2 e são comumente usados ​​em caminhões, vans e SUVs. Este engate de reboque dianteiro é avaliado para 3.500 lbs. GTW e 350 libras. TW. Ele também tem uma classificação de tração em linha reta de 9.000 lbs. Ele foi projetado para ser um engate de reboque personalizado para determinados anos do Toyota Tacoma (para verificar a compatibilidade do seu veículo, consulte as informações do aplicativo). Ele vem com todo o hardware necessário para uma instalação completa e é apoiado por uma garantia vitalícia limitada.

INSTALAÇÃO FÁCIL. Este engate de reboque dianteiro é projetado com um design específico do veículo para caber em modelos selecionados do Toyota Tacoma. RESISTENTE A CORROSÃO. Para proteção superior contra ferrugem, lascas e danos UV, este engate dianteiro é coberto por uma camada dupla de revestimento A resistente à ferrugem que reveste o engate por dentro e por fora, e um revestimento em pó preto altamente durável. CONSTRUÇÃO TESTADA. Este engate de montagem frontal é totalmente testado para sua segurança em nossas instalações de engenharia em Detroit. Testamos nossos projetos de engate de reboque dianteiro de acordo com as especificações SAE J684. FORÇA CONFIÁVEL. Este engate dianteiro é classificado para 3.500 libras. GTW e 350 libras. peso da língua. Também é classificado para 9.000 libras. capacidade de tração em linha reta para reboque de recuperação e aplicações de guincho (limitada ao componente de reboque de classificação mais baixa). RECEPTOR VERSÁTIL. Adicione um receptor de engate útil à frente do seu veículo com este engate de receptor de montagem frontal. O receptor padrão de 2 polegadas permite conectar um arado de neve, suporte de carga, bicicletário, gancho de reboque, suporte de guincho ou outro acessório de reboque.
Brand CURT
Brand ‎CURT
Country of Origin ‎USA
Customer Reviews 4.6 4.6 out of 5 stars 153 ratings 4.6 out of 5 stars
Exterior ‎Gloss Black Powder Coat
Finish Type GLOSS BLACK POWDER COAT
Item model number ‎31075
Item Weight ‎26.6 pounds
Manufacturer ‎Curt Manufacturing
Manufacturer Part Number ‎31075
Material Carbon Steel
Model ‎Front Mount Hitch
OEM Part Number ‎31075
Product Dimensions ‎44 x 15 x 8 inches
Vehicle Service Type Marine-Personal-Craft, Van, Sport-Utility-Vehicles, Truck, Trailer

3.6

10 Review
5 Star
81
4 Star
10
3 Star
2
2 Star
1
1 Star
5

escreva sua revisão

O seu email não será publicado. Todos os campos obrigatórios são marcados com*

Scritto da: RAzer
Perfect fit
Installed the hitch to mount a snow plow. It was a perfect fit for my Tacoma as it was advertised. Th installation instructions can be more specific and detailed; which would make the installation process much easier.
Scritto da: Cortney B.
Best front receiver on the market.
This this is solid I’m just not a fan of altering factory plastic it’s just a pain to get a nice finish on it. Other than that if your looking for a front receiver for a Toyota Tacoma this is #1 in my opinion.
Scritto da: David Sherritze
Nice quality bracelet
Nice product a little difficult to trim existing facia. But very good product.
Scritto da: Eugene
Excellent front receiver hitch
Hitch arrived in excellent condition. Took about 15 or twenty minutes to install. I saw many that installed hitch left off front lower fascia. There are instructions about cutting the fascia so it will fit around the hitch. I didn’t like the large gaps that would be left so I scribed my fascia to the hitch for a more custom fit. That took the rest of the day. All together, very pleased with the hitch.
Scritto da: makamai
good quality
easy install. solid.
Scritto da: Kindle Customer
Fits perfectly with required modifications
I installed this on a 2017 Toyota Pro. The instructions, which suck, state the skid plate needs to be "trimmed", but fail to explain what part of the plate needs trimmed or how much. After removing the tow hook on the passenger side and the bolt on the opposite side (driver's side) and then holding the hitch in place, it is fairly easy to determine how much of the skid plate to trim. I used a cut-off grinding wheel and cut approximately 1 and 1/2 inches off the very front of the plate. I trimmed the plate without removing it from the vehicle. Once trimmed, the hitch was easy to install. Like other complaints, it is nearly impossible to torque the top bolts; I used a box end wrench and know that I met or exceeded the torque requirements. Note that there is no air dam on a Toyota Pro, so that installation step (trimming the air dam) is not required. I installed this hitch so I could mount a receiver winch; the ground clearance is not effected by installation of the hitch, however I did purchase a hitch extender (about 20 bucks) so the winch was not resting against the license plate holder. Considering the cost of a winch bumper ($1500) and the permanent modification of the vehicle body (cutting a part of the fenders off), this is an excellent alternative. I would definitely purchase this again, or recommend it to someone who doesn't want to pay $400-$500 to modify the pickup for a winch bumper.
Scritto da: E. Seale
Great product, fit like a dream
I've got a 2017 Tacoma TRD Off-Road, and this unit installed without any issues. It's a high-quality product, and is beautifully finished (so, should handle road crud without problems). Extra bonus points -- it's built in the U.S.! It's so refreshing to be able to buy an affordably priced high-quality item that's domestically produced. I bought a similar unit for an earlier Tacoma, and got years of trouble-free service from it -- so I expect the same with this one. Some installation tips: 1) The installation instructions have good diagrams, but dark photos -- I'd recommend a quick online search to watch install videos before you start to work. 2) The mount is attached to your truck with two bolts on each end. I'd recommend you install the top bolt first (the one supplied with the unit); this way, you can leave the "cross beam insert" out while dealing with the top bolt. This gives you access to the back of the bolt, particularly handy if the thing gets loose (after you remove its "fish wire") and drops into the cross beam. This probably sounds like gibberish before you buy the unit, but it'll make sense when you have the installation instructions and parts kit in front of you. 2) The "fish wires" are a great way to get the top bolts and their spacers lined up with the appropriate holes. But once you take a bolt's fish wire off, it's free to fall back into the frame / cross beam (see tip 2, above). Fortunately there's a small hole behind this area in the frame -- I found it helped to hold the bolt in place with a skinny socket driver (something likethis ), at least until I got the respective nut started on the bolt (i.e., use the socket driver to push the bolt toward the nut).
Scritto da: C. J. Ervin
Curt quality for frount mount gear
I always buy Curt product for towing related items. Solid assembly, quality materials, competitive price and a great fit. This is a great front mount receiver for a 3rd gen Tacoma. It took 20 minutes to install. The instructions say that you will need to trim the skid plate for the TRD Off Road model, but as you can see in the images, you do not as there is ample clearance between the skid plate and the receiver.
Scritto da: JC
Excellent poduct
Fits 2017 Tacoma perfectly, installed in 35mins by Toyota mechanic (first time install). So I didn't have to get cold and dirty cost me $65 to get it install at dealership ( in Canada). match truck perfectly. Highly recomend. only bad note it came slightly damaged in shipping and seller never got back to me. for this it lose a star.
Scritto da: Robert Virtue
Good hitch for the money
Arrived in a box that was completely destroyed by shipping monkeys. However they could not destroy the hitch. Well made, piece of metal. Install was straight forward on my 2108 Toyota Tacoma Off Road. I took my time and it took me about an hour. Would buy again.

Produtos relacionados

Conheça nossa rede internacional

Enviamos para 28 países, mais de 200.000 produtos. Fique atualizado, assine a newsletter.

Array